Aprīkojums: black salami magnum железобетонный болт
Suņi: 2 vedeveshniki un 3 sauc nemednieks, ceturtais ir chigans
10.10.2019. 15:26
Nu tad kaspar tev jadodas pie frezetaja,kas arto nodarbojas visu muzu,nav nepieciedams ipass ierocu meistars,bus ari letak un kvalitate ari bus!Kad nopirku savagi virsu staveja skibi izfrezeta sliede optika staveja ar sagazumu,kiniesu dauni pat precizi nokopet nemak!Un italiem rokas ari abas kreisas!
Slēpts
10.10.2019. 15:11
Ar Sako nav vienkārši
Fitting:
A common issue with the Sako rifles is that the taper on the rifle is not the same as the taper on the picatinny rail. Contessa have designed their rail to fit as accurately as possible, tested on a wide number of Sako 85 actions. We have discovered there are slight variations in the Sako rifle dovetails due to factory tolerances, so even just a 1/100 of a mm can mean a poor fit. A method we use to overcome this poor fit is to remove the recoil stud from the rail. This should allow the rail to slide on further and tighter. If this doesn't overcome the problem, we do suggest to use Locktite where the rail dovetail surface contacts the rifle dovetail. This will ensure a solid hold. Bear in mind, any recoil actually pushes the rail forwards into the dovetail and recoil will not alone cause the rail to loosen.
* The older models of Sako with the tapered dovetail, even on the Sako 75, there are larger variations in the dovetail widths. So you may discover that the rail does not slide on fully flush with the back of the rifle. This again would require hand fitting to the rifle. If you need any advice on hand fitting please contact us.
Jāni pirku Anglijā, ražota Itālijā. Izstrādājums labs (smuks).... vienīgi neder.
Oriģināli diemžēl Sako 75 modelim šāda izstrādājuma nav (vismaz es neatradu interneta plašumos)...
Sako wever bloki ir trīs grupās atkarībā no kalibra, to jau ņēmu vērā. Vēl protams modifikācijas ar MOA sākot no 0 un beidzot ar +20
Bet neder, kaut arī rakstīts, ka atbilst Sako 75/85
Fitting:
A common issue with the Sako rifles is that the taper on the rifle is not the same as the taper on the picatinny rail. Contessa have designed their rail to fit as accurately as possible, tested on a wide number of Sako 85 actions. We have discovered there are slight variations in the Sako rifle dovetails due to factory tolerances, so even just a 1/100 of a mm can mean a poor fit. A method we use to overcome this poor fit is to remove the recoil stud from the rail. This should allow the rail to slide on further and tighter. If this doesn't overcome the problem, we do suggest to use Locktite where the rail dovetail surface contacts the rifle dovetail. This will ensure a solid hold. Bear in mind, any recoil actually pushes the rail forwards into the dovetail and recoil will not alone cause the rail to loosen.
* The older models of Sako with the tapered dovetail, even on the Sako 75, there are larger variations in the dovetail widths. So you may discover that the rail does not slide on fully flush with the back of the rifle. This again would require hand fitting to the rifle. If you need any advice on hand fitting please contact us.
Oriģināli diemžēl Sako 75 modelim šāda izstrādājuma nav (vismaz es neatradu interneta plašumos)...
Bet neder, kaut arī rakstīts, ka atbilst Sako 75/85